Bosch B450 Instalační příručka Strana 98
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Notice!
If Lockout Report is enabled for any zone, the last restore signal is not transmitted until the
system is disarmed.
Example
Zones 1 and 2 are programmed for lockout report with a Swinger Shutdown Count of 6. If
Zone 1 activates an alarm, the Swinger Shutdown Count increments to 1 when the control
panel sends the reort.
If Zone 1 reactivates the report, the Swinger Shutdown Count is incremented to 2. If Zone 1
reactivates the report three more times, the Swinger Shutdown Count is 5.
If Zone 2 activates an alarm, the Swinger Shutdown Count for Zone 2 is incremented to 1.
Swinger Shutdown Count for Zone 1 is still 5. If Zone 1 reactivates again, it locks out Zone 1
from activating the report until the system is reset. At this point, the Swinger Shutdown Count
for the Report is reset to 0 and Zone 1 is locked out. When smart lockout is enabled, if any
zone activates the siren before siren running time is expired, Zone 1 reactivates and can still
send a report.
System Status Programming
System Status Reporting Options
Location 427 is set by default to report only to Receiver 1. You can select whether System
Status Reports are sent to Receiver 1, Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or no reporting.
Item Location Default
System Status Reporting Options 427 1
Value Description
0 No Reports allowed
1 Report to Receiver 1
2 Report to Receiver 2
4 Report to both Receiver 1 and Receiver 2
8 Report to Receiver 2 only if Receiver 1 fails
Test Reporting Time
A Test Report (Contact ID Event Code 601/602) is a specific signal sent to the base station
receiver and is normally used to test the dialing and reporting functions of the control panel.
When programming Test Report options, specify the hour and minute of the day the report is
required, and how often to send the report. Test reports are reported on a daily basis from
every day to every fifteen days. Program the Test Report Time as 34:00 to send reports every
60 minutes.
Example
Set auto test report interval to the 37
th
minute of every hour, the time needs to be set as
34:37. Then the auto test report will be sent at 00:37, 01:37, 02:37, etc.
If you want to send Test Reports once every seven days at 11:35 PM (23:35), program
Locations 428 to 431 as [2 3 3 5] and location 434 as [7].
9.6
9.6.1
9.6.2
98 en | Zone Information Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch B450
(20 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce