Bosch B450 Instalační příručka Strana 63
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
– RFSM
You can allocate only one wireless device to each zone.
To program an RF wireless device:
1. Use the installer code to configure the RF receiver as RADION receiver (address=395).
Save the changes and Exit programming mode.
2. Enter the Installer Code and press [0][AWAY]. Two beeps sound and the STAY and AWAY
indicators flash.
3. Enter the RF device number (1 to 16) you want to change and press [AWAY]. Two beeps
sound and the corresponding codepad indicator lights to show the RF device number you
selected.
4. There are two ways to enter the RFID:
– Enter the nine-digit RFID number found on the back of the RF device and press
[AWAY]. Two beeps sound. The control panel will sound one error beep and exit if
the wrong check-sum or a duplicated RFID number is entered.
– Press [AWAY] to switch into auto-learn mode. Note that all the codepad indicators
(1~16) flash on the icon codepad. Trigger the wireless device. The control panel will
sound 3 beeps and learn the RFID. The last digit of the RFID number is displayed on
the codepad. Press [AWAY] to confirm. If the zone has already been used in the
system, the panel will ignore this RFID.
5. Enter one zone input option value (0~15). Press [AWAY] to finish this function and reset
the control panel.
6. The user can press [STAY] to cancel the wireless zone enrollment at any step except
during the delete process. The codepad sounds one error beep, cancels the enrollment,
and exits.
Notice!
This function is automatically terminated if you do not press a button within 40 sec or if you
press [AWAY]. One long beep indicates that you selected an incorrect user number.
Example:
To program RF wireless device number 3 whose 9- digit ID number is 000094946, enter [1 2 3
4 0][AWAY][3][AWAY] [0 0 0 0 9 4 9 4 6][AWAY][AWAY].
To delete an RF wireless device:
1. Enter the Installer Code and press [0][AWAY]. Two beeps sound and the STAY and AWAY
indicators flash.
2. Enter the RF device number (1 to 16) you want to delete and press [AWAY]. Two beeps
sound and the corresponding codepad indicators light to show the RF device number you
selected.
3. Press [STAY] to delete the RF device. The STAY and AWAY indicators are extinguished.
4. Repeat steps 1 to 3 to delete another RF wireless device.
Set the Number of Days until the First Test Report
This function determines when the system sends the first Test Report (Contact ID Event Code
602). If you do not use this Installer Code function, the first Test Report is sent to the base
station receiver after the repeat interval programmed in Location 428 (refer to Test Reporting
Time, page 98). If you want the system to send the first Test Report sooner than the repeat
interval, use this function to set when the first Test Report is sent.
To set the first Test Report:
7.1.2
Control Panel System Functions | en 63
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch B450
(20 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce