Bosch B450 Instalační příručka Strana 28
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
B308 Octo-output Module
The B308 Octo-output Module is a supervised device that provides 8 programmable outputs
(Form C relays) and connects to control panels through the SDI2 bus. Each output provides
dry contact switching rated for a maximum of 1.0 A at 24 VDC. The outputs are accessed
through on-board screw terminal connections. The address switches are used to set the
module’s SDI2 address. Control panel programming determines each output’s response to
specific events. The B308 receives serial data from the control panel and activates outputs in
response to control panel conditions and settings. Outputs can be programmed for remote
control from a control panel codepad or computer (A-Link) or smartphone application (RSC).
Set the address
Two address switches determine the address for the B308 Octo-output Module. The control
panel uses the address for communications. Use a slotted screwdriver to set the two address
switches. Set the address switches per the control panel configuration.
The module’s address switches provide a tens and ones value for the module’s address. Set
the tens switch to 0 and the ones digit 1.
Notice!
The module reads the address switch setting only during power up. If you change the
switches after you apply power to the module, you must cycle the power to the module in
order for the new setting to be enabled.
Install the module
After you set the address switches for the proper address, install the module in the enclosure.
Mount the module into the enclosure’s 3-hole mounting pattern using the supplied mounting
screws and mounting bracket.
Notice!
Remove all power (AC and battery) before making any connections. Failure to do so might
result in personal injury and/or equipment damage.
Wire to the control panel
When you wire the module to a control panel, use the module’s terminal strip labeled with
PWR, A, B, and COM.
LED descriptions
The module includes one blue heartbeat LED to indicate that the module has power and to
indicate the module’s current state.
Flash pattern Function
Flashes once every 1 second Indicates normal operation state.
3 quick flashes every 1 second Indicates the module is in a “no communication” state
resulting in an SDI2 communication error.
4.4
28 en | Accessories Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch B450
(20 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce