Bosch B450 Specifikace stáhnout pdf

1 | Overview

3.2 | Install the module

2 | SDI2 address settings

You can congure the B450 using one of the methods described

in this section for your control panel type.

4 |

Conguration

4.1 |

Plug and play conguration

When installing under the following conditions, the B450 needs

no further conguration to communicate:

– AES Encryption is not required.

– Low signal delay can be no more than 200 sec.

4.2 |

Conguring with SDI2 control panels

An SDI2-compatible control panel automatically congures a

connected module.

1. Power off the compatible control panel.

2. Set the address switch to the correct address for the control

panel (SDI2 control panels use address 1 or 2).

3. Connect the module to the control panel bus and apply

power.

4. Program the control panel communication settings using

RPS or the keypad.

4.3 |

Conguring with SMS

The B450 supports conguration by SMS. You can send SMS via

mobile phone to the B450. For more information, refer to the

B450 Installation and Operation Guide.

Mount the B450 into the enclosure’s 3-hole mounting pattern

using the supplied mounting screws, and secure the antenna

onto the enclosure. Mount the B450 into the interior side of

the enclosure. Refer to Figure 3.2.

Callout ― Description

1 ― B450

2 ― Enclosure

3 ― Mounting screws (3)

4 ―

B44x plug-in cellular communicator antenna (routed through

any knock-out)

5 ― B44x plug-in cellular communicator antenna cable (connected

to the communication module)

Figure 3.3: Installing the module

3.3 | Wire to the control panel

When wiring a B450 to a control panel, you can use either the

module’s terminal strip labeled with PWR, A, B, and COM or

the module’s interconnect wiring connectors (wire included).

Interconnect wiring parallels the PWR, A, B, and COM terminals

on the terminal strip. Figure 1.1 indicates the location of both

the terminal strip and the interconnect connect connectors on

the module.

3 | Installation

Perform the following steps to install the B450.

2.1 | Set the B450 address

3.1 | Insert the module into the B450

Figure 3.3: Using SDI2 terminal strip or SDI2 interconnect cable

wiring (B5512 control panel shown).

Callout ― Description

1 ― SIM card

2 ― B44x cellular communication module (available separately)

3 ― B450

Figure 3.1.2: Inserting the communication module

Insert the communication module into the slot of the B450,

depending on your communication module (one with a SIM

card, or one without). Refer to Figure 3.1.2.

Callout ― Description

1 ― Control panel (B5512 shown)

2 ― B450 module

3 ― Terminal wiring strip

4 ―

Interconnect wiring (P/N: F01U079745) (included)

The B450 address switch determines the bus address of

the device. Set the address switch per the control panel

conguration. If multiple B450 devices reside on the same

system, each B450 module must have a unique system address,

and cannot share the same address value. Figure 2.1 shows the

address switch settings for address 01. Refer to Table 2.1 for

panel-specic settings.

The address switch determines the bus address for the

B450 module. The control panel requires the address for

communications. Use a slotted screwdriver to set the address

switch.

NOTICE!

The module reads the address switch setting only

during power up. If you change the switch after

you apply power to the module, you must cycle the

power to the module in order for the new setting to

be enabled.

Figure 2.1: Address switch set to address 1

Control Panels Switch

Position

Control

Panel

Address

Bus

Type

Function

USB or SMS

conguration setting

0 n/a Any Change

Conguration

B5512/B4512/B3512/

D9412GV4/D7412GV4/

D7212GV4/

Solution 2000/3000

1 1 SDI2 Automation, RPS,

or Reporting

D9412GV4/D7412GV4/

D7212GV4

Solution 2000/3000

2 2 SDI2 Automation, RPS,

or Reporting

D9412GV4/D7412GV4/

D7212GV4/D9412GV3/

D7412GV3/D7212GV3

D9412GV2/D7412GV2/

D7212GV2 v7.06+

4 88 SDI

RPS or Reporting

D9412GV4/D7412GV4/

D7212GV4

D9412GV3/D7412GV3/

D7212GV3

5 92 SDI

RPS or Reporting

AMAX 2000/2100/3000/

4000

CMS 6/8/40

Easy Series v3+

6 134 Option RPS or Reporting

FPD-7024 v1.03+ 9 250 Option RPS or Reporting

For D9412GV4/D7412GV4/D7212GV4 congurations, SDI2 bus connection

is the recommended conguration option, but SDI bus conguration is also

supported.

NOTICE!

Power up the B450 with the address switch set

to the desired bus. When ready to program using

SMS, turn the switch to position 0. When done

programming, turn the switch back. Failure to return

the address switch to the previous setting will result

in a troubled condition.

NOTICE!

Remove power to the control panel prior to wiring

a B450 module to the control panel using either the

terminal strip wiring or interconnect cable to wire to

the control panel. Do not use both.

NOTICE!

UL requires that for security installations, the B450

module be installed in a UL Listed enclosure with a

tamper.

The B450 Bus Communicator Interface Module (wired to a

compatible control panel) is a four-wire powered SDI2, SDI, or

Option bus device that provides two-way communication over

commercial cellular networks using a plug-in communicator.

The B450 on-board rotary switch determines the bus address of

the device. Conguration of the B450 is performed via USB or

SMS. On SDI2 control panels conguration can also be done on

the keypad or through Remote Programming Software (RPS).

Figure 1.1: Board overview

Callout ― Description

1 ― Tamper switch connector

2 ― Address switch

3 ―

MODE 2-pin connector (for future use)

4 ― Bus address label

5 ― USB connector

6 ― Heartbeat LED

7 ― RX LED (indicates packets received from the wireless network)

8 ― TX LED (indicates packets transmitted over the wireless net-

work)

9 ― Terminal strip (to control panel bus)

10 ―

Interconnect wiring connectors (to control panel bus or other

compatible modules)

1 2

Callout ― Description 1

Shrnutí obsahu

Strany 1 - Callout ― Description

1 | Overview3.2 | Install the module2 | SDI2 address settingsYou can congure the B450 using one of the methods described in this section for your con

Strany 2

Bosch Security Systems, Inc.130 Perinton ParkwayFairport, NY 14450USAwww.boschsecurity.comBosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 Grasbr