Bosch B450 Instalační příručka Strana 83
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Zone Information
Day Alarm Information
Location 265
Default 0
1 Zone 1
2 Zone 2
4 Zone 3
8 Zone 4
This location has four programming options. You can select any combination of the options by
programming a single value. Calculate this value by adding the option bit numbers together.
Day Alarm allows some zones to be monitored when the system is disarmed. Indications are
available at any of the programmable outputs, including the codepad buzzer. This function
accommodates latching and non-latching Day Alarm Output Event Types.
When the system is armed in AWAY Mode, STAY Mode 1, or STAY Mode 2, zones programmed
as Day Alarm Zones activate the sirens and report just as non-Day Alarm Zones do. When Day
Alarm is activated, it ignores any zone Pulse Count settings programmed for that zone (that is,
the zone Pulse Count is only relevant when the system is armed).
Example
You can set up a Day Alarm at the front door of a shop with a pressure mat or electronic beam
that is activated when a customer enters the shop. When a customer walks on the pressure
mat or breaks the electronic beam, the codepad buzzer beeps.
Day Alarm Resetting
An output that is programmed for Day Alarm Resetting operates when a zone programmed for
Day Alarm is activated. The output is reset after the zone is resealed. This occurs only when
the system is disarmed. Refer to Output Event Types, page 132 for more information.
Day Alarm Latching
An output that is programmed for Day Alarm Latching operates when a zone programmed for
Day Alarm is activated. The zone indicator and the latching output resets when [AWAY] is
pressed. This occurs only when the system is disarmed. Refer to Output Event Types, page 132
for more information.
Day Alarm Operation
If a zone is programmed for Day Alarm, the zone can be isolated in the normal way so that it
does not register as a Day Alarm Zone when the system is disarmed. You can use only Zones 1
to 4 as Day Alarm Zones.
You can program the STAY indicator to indicate whether Day Alarm is turned on or off by
selecting Option 8 in Location 496 (refer to Consumer Options 1, page 108). When Day Alarm
is on, the STAY indicator flashes once every 3 seconds.
You can program an output to mimic a zone for monitoring Zones 5 to 8. Refer to Output Event
Types, page 132.
To turn Day Alarm on:
Press and hold [4] until three beeps sound.
9
9.1
9.1.1
9.1.2
9.1.3
Control Panel Zone Information | en 83
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch B450
(20 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce