Bosch B450 Instalační příručka Strana 126
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Authority Levels Description
12 Master Code and Arm/Disarm and Code Required to Isolate
14 Master Code and Arm/Disarm and Code Required to Isolate and Arm/Disarm
Reports
Table 14.1: Authority Levels
The purpose of User Codes is to arm and disarm the system and to perform other specific
functions. A Master Code holder can change or delete User Codes at any time.
User Codes 1 to 32 can be one to four digits long, but all user codes should be the same
length. Each User Code has its own priority level. More than one User Code can have the same
priority level. The priority level controls the behavior of the code, such as allowing it to arm
only, arm and disarm, or allow access to the Master Code functions. The installer can assign
access to Master Code functions to multiple User Codes. The priority level for each User Code
is programmed in the last location of the code.
Notice!
Only the installer can change the priority level.
There are 32 User Codes and 32 RF User Codes, RF User Codes can only be Remote Radio
User Codes.
Special User Code is reported when any of these methods are used to arm or disarm the
system:
– User Code 998: Arming and disarming using the A-Link Plus software.
– User Code 995: Arming remotely by telephone.
– User Code 000: Single button arming/disarming in AWAY Mode, STAY Mode 1, or STAY
Mode 2.
– User Code 997: Automatic arming/disarming in AWAY Mode or STAY Mode 1.
User Code Priority
The installer can assign one of ten different priority levels to a User Code. Each priority level
allows or restricts a user from performing specific functions.
Arm/Disarm
The user can arm and disarm the system. An Arming Report is sent only after a previous code
with the ability to send a Disarming Report disarms the system.
Arm Only
The user can arm the system but cannot disarm the system. An Arming Report is sent only
after a previous code with the ability to send a Disarming Report disarms the system.
Arming/Disarming Reports
Arming/Disarming Reports are sent to the monitoring station when the user disarms and arms
the system.
Code To Isolate
If one or more User Codes include this option, the method of standard isolating is disabled
and only a User Code with this option in its priority level can isolate zones before arming the
system using the Code to Isolate method.
14.3
126 en | Access Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch B450
(20 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce