Bosch DS7400XiV4-EXP Specifikace stáhnout pdf (Strana 73)

DS7400XiV4-EXP | Reference Guide | 5.0 Programming the Control Panel EN | 73

Bosch Security Systems | 1/05| 4998154963B

5.9.33 Pager Delay Time

When using the Pager Dialing Format (selected in

Addresses 3156 and 3157; see Section 5.9.31 Phone

Number Format Programming), you can insert a delay

time after the phone number is dialed and before the

reports are sent to the pager system. This delay allows

greeting and instruction messages in the pager system.

This delay does not affect any other report formats.

The delay time is a two-digit number, programmed

across both data digits. For example, to set a delay time

of 5 seconds, make Data Digit 1 = 0 and Data Digit 2 =

5. The default delay time = 10 seconds (Data Digit 1 =

1 and Data Digit 2 = 0).

• Address: 4038

• Data Digit:

• Data Digit 1: ____ (default = 1)

• Data Digit 2: ____ (default = 0)

• Selections: 0 to 9

• Delay Time Range: 00 to 99 seconds

5.9.34 Programmer’s and Master Code

Programming (Addresses 7589 to 7592)

Programmer’s Code programming defines the

Programmer’s Code. This code is used to enter

Programming Mode from the keypads.

Although the DS7400Xi (Ver. 4+) Control

Panel is pre-programmed with 6-digit codes,

it is also shipped with a 4-digit PIN length

default. The default codes for the

Programmer’s Code and the Master Code

are 4-digits (9876 and 1234 respectively)

unless you reprogrammed for a 6-digit PIN

length.

Programmer’s Code

Enter the Programmer’s Code as six digits.

The Programmer’s Code cannot be the

same as any PIN number.

• Address: 7589

• Data Digit:

• Data Digit 1: ____ (default = 9)

• Data Digit 2: ____ (default = 8)

• Data Digit 3: ____ (default = 7)

• Data Digit 4: ____ (default = 6)

• Data Digit 5: ____ (default = 5)

• Data Digit 6: ____ (default = 4)

• Selections: 0 to 9

• Default: 987654

Master Code

Master Code programming defines what the Master

Code will be. This code is the highest authority level

for a PIN.

If the Master Code is lost, use this address to program

a new one. Otherwise, the Master Code Programming

Mode should be used to create PINs that have a Master

Code authority level.

Master Code for User Number 001 has its authority

fixed at Level 0. It will always have access to all areas.

User Numbers 002 through 200 must be

programmed from the Master Code

Programming Mode.

• Address: 7592

• Data Digit:

• Data Digit 1: ____ (default = 1)

• Data Digit 2: ____ (default = 2)

• Data Digit 3: ____ (default = 3)

• Data Digit 4: ____ (default = 4)

• Data Digit 5: ____ (default = 5)

• Data Digit 6: ____ (default = 6)

• Selections: 0 to 9

• Default: 123456

5.9.35 PIN Length Programming

PIN Length Programming defines the length of the

PINs that are assigned to each user. PINS can be

programmed to be 4 or 6 digits in length.

• Address: 3478

• Data Digit:

• Data Digit 1: ____ (see Table 101; default = 0)

• Data Digit 2: Must = 0

• Selections: 0 or 1

Table 101: Address 3478, Data Digit 1

Select Option Value

4-digit PINs

6-digit PINs 1

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Specifikace Strana 73

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP