Bosch DS7400XiV4-EXP Specifikace stáhnout pdf (Strana 118)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 118

Bosch Security Systems | 1/05| 4998154963B

Close: This report is sent when the system has been

armed. In SIA or Contact ID formats, the user number

for the person who armed the system will be sent with

this report. To send the user number along with a Close

report in other formats, program the extended digit of

the report as *5. In Contact ID format, the area number

will also be sent along with this report.

Duress: This report is sent when the system is disarmed

using a duress code. The user number is not sent with

this report.

Partial Close: This report is sent when the system is

armed partially, or force armed.

First Open After Alarm: This report is sent when the

system is disarmed after an alarm has occurred.

Low Battery: This report is sent when a low battery

condition occurs.

Battery Restoral: This report is sent when a low

battery condition restores.

AC Fail: This report is sent when an AC failure

condition occurs. This report may be delayed in address

4034.

AC Failure Report Delay: The AC power loss report

can be programmed to delay for up to 254 minutes (see

Section 5.9.21 AC Fail Report Delay Programming). (The

same delay would also apply to the AC restoral report.)

• If another report is sent during this delay period,

the AC fail report will be sent along with this

report.

• If the AC power restores during this delay period,

the AC loss report will not be sent.

• Programming address 4034 as FF causes the report

to be sent at a random interval of at least 15

minutes, but no more than 2 hours after the AC

failure occurs.

AC Restoral: This report is sent when an AC failure

condition restores.

Communicator Test/System Normal: This report is

sent at the 24-hour check-in time if there is not a control

panel trouble, an active fire alarm that has not been

acknowledged, a fire trouble, or a supervisory

condition. Note: To send a Communicator Test even if

one of these conditions exists, program the

Communicator Test/System Off Normal.

Remote Program Successful: This report is sent after a

Remote Program session, if the session was terminated

properly.

Remote Program Unsuccessful: This report is sent

after a Remote Program session, if some error has

occurred or the session did not terminate properly.

Local Program Successful: This report is sent when

local programmer's mode is exited and there is no

error associated with the programming.

Local Program Unsuccessful: This report is sent

when local programmer's mode is exited and there has

been some error associated with the programming.

System Trouble: This report is sent when a control

panel trouble condition occurs.

System Trouble Restoral: This report is sent when all

system trouble conditions restore.

Communicator Test/System Off Normal: This

report is sent at the 24-hour check-in time if there is a

control panel trouble, an active fire alarm that has not

been acknowledged, a fire trouble, or a supervisory

condition.

Exit Error: This report is sent if an exit error occurs.

An exit error occurs when an entry/exit zone is still

violated at the end of the exit delay. If this happens,

the entry delay will begin and any output programmed

to activate an alarm will energize. If the system is not

disarmed before the entry delay expires, an alarm

report for the effected zone will be sent and the Exit

Error report will be sent. If this report is not

programmed, the control panel will not sound the exit

error warning.

Recent Closing: This report is sent, along with any

alarm reports, when there is an alarm within the first

five minutes after the system has been armed.

System Walk Test: This report is sent when a system

test has been started ([#][8][1] key sequence). Zone

reports are sent during a system test.

System Walk Test Restoral: This report is sent when

the system test has been completed or has timed-out.

Fire Walk Test: This report is sent when a Fire Walk

Test has been started ([#][9][1] key sequence). Zone

reports are not sent during a Fire Walk Test.

Fire Walk Test Restoral: This report is sent when the

Fire Walk Test has been completed or has timed-out.

Dirty Chamber Report: This report is sent when a

MX250 Series smoke detector fails to pass the

"Chamber Check

" sensitivity test.

Dirty Chamber Restoral: This report is sent when a

MX250 Series smoke detector has been returned to

normal operation after service.

1 2 ... 113 114 115 116 117 118 119 120 121 122 123 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Specifikace Strana 118

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP