Bosch DS7400XiV4-EXP Specifikace stáhnout pdf (Strana 17)

DS7400XiV4-EXP | Reference Guide | 3.0 Control Panel Installation EN | 17

Bosch Security Systems | 1/05| 4998154963B

Figure 7: Zones 1 to 8 Wiring

17 18 19 20 21 22 23 24 25 26 27 28 29 30

PO1 PO2

1–

L+

2– 3– 5– 6– 7– 8–4–

L+ L+ L+

EOL = 2.2k

3.8 Programmable Output Wiring

See Figure 7, Terminals 17 and 18. PO1 shorts to aux.

power negative when activated. PO1 can sink up to 1.0

A. PO1 function is programmed in Address 2735. See

Section 5.9.6 Output Programming.

PO2 supplies 12 V and up to 500 mA when activated.

PO2 function is programmed in Address 2736. See

Section 5.9.6 Output Programming.

Figure 8: Typical Burglar and Fire Wiring

Z– L+ Z– L+

–

Z– L+

432

1011

1 12

1- Zone Input

2- Loop +

3- Loop + or PO2

4- Aux. Power – Terminal 5 or 7(see Figure 3)

5- Power in

6- Power out

7- Alarm

8- End-of-line supervision relay (for example,

EOL200)

9- Typical 4-wire smoke detector wiring (for

example, DS250 in an MB4W base)

10- Typical 2-wire smoke detector wiring

(EOL = 2.2k)

11- Typical burglar alarm loop wiring (EOL = 2.2k)

3.9 Option Bus Wiring

See Figure 9. Used for options such as the DS7416i

Communications Module, the DS7420i Dual Phone

Line Module, and so on. Also for Keypads 11 to 15.

For Commercial Fire Mode, Option Bus wiring should

be in conduit if run outside the enclosure.

Figure 9: Option Bus Wiring

1- Option Bus

3.10 Hardware Layout Example

See Figure 10.

• Up to 15 keypads can be used. Keypads 1 to 10

connect to the Keypad Bus and Keypads 11 to 15

connect to the Option Bus. One keypad must be

designated as Keypad 1 and connected to the

Keypad Bus. See the DS7447E/DS7447V2,

DS7445i/DS7445V2, and DS7448 Installation

Instructions for further details.

• A DS7420i (Dual Phone Line/Bell Supervision

Module) can be connected to the control panel,

and placed within the enclosure. Connect to the

Options Bus of the control panel. See the

appropriate keypad Installation Instructions for

further details.

• Up to two DX3010 Octal Relay Modules can be

connected to the control panel and placed within

the enclosure. Connect to the Option Bus of the

control panel. This provides an additional 8 Form

“C” relay outputs for the Control Panel. See the

DX3010 Installation Instructions for further details.

• A DS7430 or a DS7436 (Multiplex Expansion

Module) can be connected to the control panel

using the expansion port. This allows for the

connection of additional zones using the Option

Bus. See the DS7430 or DS7436 Installation

Instructions for further details.

• Up to 30 DS7432E 8-Input Remote Modules can

be connected to the DS7430 or DS7436. Connect

to the Power and Bus Terminals of the Multiplex

Expansion Module. This allows for a means of

addressing up to 240 input loops of conventional

contacts to the control panel. See the DS7432E

Installation Instructions for further details.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Specifikace Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP