Bosch DS7400XiV4-EXP Specifikace stáhnout pdf (Strana 21)

DS7400XiV4-EXP | Reference Guide | 4.0 Operating Guide EN | 21

Bosch Security Systems | 1/05| 4998154963B

Table 8: Authority Levels (continued)

Level

Number

Level

Name

Description

4 Temporary Valid only for a specified time

(the PIN expires on the

expiration date). It can arm and

disarm the system, but cannot

perform any other functions. If

this is done from a Master

keypad, the user must be in

Single Partition Mode. If access

is assigned to more than one

area, you must enter a

Temporary PIN expiration date

for all assigned areas (see

Changing the Expiration Date

for Temporary PINs below).

5 Duress When the system is disarmed

using the duress code, a silent

report is sent to the monitoring

service. The Duress code is

intended to be used when the

user is forced to disarm the

system.

6 Access

Code

When a PIN with an Access

Code is entered, any output

programmed for Access Output

(i.e. door strikes) pulses on for

10 seconds (works when the

system is armed or disarmed).

4.4.2 Programming PINs

PINs can only be added, changed, or removed in

Master Programming Mode; they are not

programmable from an RF (wireless) keypad.

Write down your entries before you enter the Master

Code Programming Mode and have them with you as

you begin programming. Make your entries promptly.

If a long delay occurs in your entries, the 3-beep error

tone sounds and exits you from the programming

mode.

It is recommended that all PIN programming

procedures be performed at a DS7447E/DS7447V2

keypad since this keypad provides visual prompts

throughout the programming sequence. No visual

clues are given from a DS7445i/DS7445V2 keypad.

When the programming sequence is successfully

completed, both the DS7447E/DS7447V2 and

DS7445i/DS7445V2 keypads signal the successful

completion with a long beep.

Perform the following procedure to add or change a

PIN:

If you are adding a temporary PIN, you

must enter the expiration date before

adding the temporary PIN.

1. Enter Master Programming Mode (press [Master

PIN][#][0]).

2. Enter a 0 for PIN Setup programming (press [0]).

3. Enter the User Number (enter a 3-digit number

from 001 to 200).

4. Enter the Authority Level (enter a number from 0

to 6).

5. Enter the Area(s) (Partitions) to which this user will

have access (press [1], [2], [3], [4], [5], [6], [7],

and/or [8] followed by [#]).

6. Enter the PIN (enter any 4- or 6-digit number; do

not press [#]).

7. Enter the PIN again followed by [#].

Perform the following procedure to set the

expiration date for an existing Temporary PIN:

1. Enter Master Programming Mode (press [Master

PIN][#][0]).

2. Enter a 3 for Date of Code Expiration Setup

programming (press [3]).

3. Enter the Expiration Month (press [0][1] for

January through [1][2] for December).

4. Enter the Expiration Day (press [0][1] through

[3][1]). The Temporary PIN expires at Midnight on the

day selected.

5. Enter the Year (enter the last two digits of the year

followed by [#]).

Entering the command sequence [Master

Code][#][0][3][#] causes the

DS7447E/DS7447V2 keypad to read back

the temporary code expiration date.

Perform the following procedure to remove a PIN:

1. Enter Master Programming Mode (press [Master

PIN][#][0]).

2. Enter a 0 for PIN Setup programming (press [0]).

3. Enter the User number of the PIN to be cancelled,

followed by [#] (enter a 3-digit number from 001

to 200, then press [#]).

User Number 001 cannot be disabled in

this manner.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Specifikace Strana 21

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP