Bosch DS7400XiV4-EXP Specifikace stáhnout pdf (Strana 110)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 110

Bosch Security Systems | 1/05| 4998154963B

If you are programming a single input device,

press [#] to contiune. The text keypad shows:

Sensor? Press 4

Contact? Press 6

Press [4] to enter sensor devices into the control

panel. Press [6] to enter contact devices into the

control panel.

The keypad sounds a single beep and scrolls to

the next zone if the device is properly entered.

If the zone is not programmed properly, the

keypad sounds a three-beep error tone.

e. Disconnect the device you just programmed

from the DS7430, and connect the next device.

Press [#] to continue programming.

24-hour zones will alarm when you exit the

programmer’s mode. Alarm reports for

these zones are sent if programmed. If you

do not want these reports sent, remove

power from the system now by

disconnecting the transformer and the red

battery lead. Do not reconnect power until

all zones are installed and connected to the

multiplex bus.

If there are no other multiplex zones to

program, the text keypad shows:

Mux Zone

Enter Zone

Press and hold [Reset/*] for two seconds to exit

the zone programmer’s mode. This returns you

to the programmer’s mode. Press and hold

[Reset/*] for two more seconds to exit the

programmer’s mode.

To disable or remove a multiplex zone, set the

program address’s data digits to 00.

7.2 Glossary

7.2.1 General Control Programming

Normal Arming: [PIN][On]: If programmed, arms the

entire system while allowing entry delays for entry/exit

zones.

Perimeter Instant Arming: [PIN][No Entry][Perimeter

Only]: If programmed, arms only the perimeter of the

system and does not allow entry delays for entry/exit

zones.

Perimeter Arming: [PIN][Perimeter Only]: If

programmed, arms only the perimeter of the system

while allowing entry delays for entry/exit zones.

Custom Arming: [PIN][#][4]: If programmed, allows

custom arming of the system and bypasses the zone

functions specified in data addresses 2725-2728.

Maximum Security Arming: [PIN][No Entry][On]: If

programmed, arms the entire system and does not

allow an entry delay for entry/exit zones.

General Authority by Area: A general (level 2)

authority can be programmed to have arm-only

authority; arm and bypass authority; arm and disarm

authority; or arm, disarm, and bypass authority by

area. This is done at addresses 3421-3424.

• Arm-only access by area allows someone with a

General Authority to arm zones in an area he can

not disarm.

• This level can still be used to arm, disarm, and

bypass zones in the other areas that it has access

to.

Closing Ring-Back: If programmed, the keypad

sounders and Bell will activate for 2 seconds after the

system is armed and the closing report is successfully

sent. This requires Closing Ring-Back and Closing

Report to be programmed.

• If a closing report is not programmed, the control

panel will test for a dial tone when the system is

armed. If the test passes, the system will arm

normally. If the test fails, the system will arm, but

will indicate a trouble condition.

• The DS7447E/DS7447V2 keypad will display

"Communication Err" after [#][8][7] is entered.

Siren on Comm. Fail for Silent Zone: If

programmed, a silent zone will sound the alarm

outputs if the zone is in an alarm condition and the

system fails to communicate with the central station.

Restore when Sounders Silence: If programmed, a

zone sends a restoral report and is ready to activate

again only after the burglary bell cut-off time expires

or the bells are silenced.

• The zone can alarm multiple times per armed

period.

Restore when Zone Restores: If programmed, a zone

sends a restoral report and is ready to activate again as

soon as it physically restores.

• This zone can alarm multiple times per armed

period.

Restore when System Disarms: If programmed, a

zone sends a restoral report when the system is

disarmed.

• It can only alarm once per armed period.

1 2 ... 105 106 107 108 109 110 111 112 113 114 115 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Specifikace Strana 110

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP