Bosch AMAX panel 4000 EN Instalační příručka Strana 50
- Strana / 176
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
– If there are two or more zones programmed as delay zones and both are triggered,
the follower zone will follow the first triggered delay zone
3. STAY ARM: same as the delay zone.
6 - Interior Follower
The interior follower zone will perform as below:
1. Disarm: same as the Instant Zone disarm status
2. AWAY Arm: same as the Follower Zone AWAY Arm status
3. STAY Arm:
– This zone will be ignored and performed as disarm.
– Refer to Section Keypad Indicators, page 20 to see how the zone is displayed during
exit time.
7 - 24 Hour Zone
The 24 Hour zone will perform as below:
1. Disarm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
2. AWAY Arm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
– Zone triggered - during exit time - Alarm / report
– Zone triggered - during entry time - Alarm / report
3. STAY Arm: Same as AWAY Arm performance.
– A 24 Hour zone does not send a restore report until the zone is restored.
8 - Tamper Zone
The Tamper zone will perform as below:
1. Disarm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
2. AWAY Arm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
– Zone triggered - during exit time - Alarm / report
– Zone triggered - during entry time - Alarm / report
3. STAY Arm: Same as AWAY Arm performance.
– A Tamper zone does not send a restore report until the zone is restored.
9 - Fire Zone
The Fire zone will perform as below:
1. Disarm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
2. AWAY Arm:
– Zone normal - no Alarm / no report
– Zone triggered - Alarm / report
– Zone triggered - during exit time - Alarm / report
– Zone triggered - during entry time - Alarm / report
3. STAY Arm: Same as AWAY Arm performance.
50
en | Settings
AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
- Table of contents 3
- 4 en 4
- Table of Contents 5
- 6 en 6
- Graphics 7
- 8 en 8
- Short Information 9
- System overview 10
- Brief Introduction 11
- Address Setting 11
- Wiring and Installation 12
- Alarm Control Panel 13
- DIP Switch 16
- Status Indicator 16
- Installation 17
- Press latch 23
- Wall Tamper 24
- Address Jumper 26
- E N √ E N √ 29
- Backup Battery 30
- Installation 31
- Settings 32
- Receiver Subscriber ID Number 33
- Receiver Transmission Format 33
- 34 en 34
- Settings 35
- 36 en 36
- Settings 37
- Dual IP 38
- System Reporting 39
- Settings 41
- Settings 43
- 44 en 44
- Domestic Call 45
- Zone Inputs 46
- BBBBB7DPSHU6ZLWFK 47
- BBBBB=RQH6ZLWFK 47
- Settings 49
- Settings 51
- 52 en 52
- Settings 53
- Settings 55
- Adding and Changing Zone 57
- Onboard / Extension Output 58
- Output Events 58
- Settings 59
- Settings 61
- Output Options 63
- 64 en 64
- Settings 65
- 66 en 66
- Settings 69
- Settings 71
- Settings 73
- Settings 75
- Settings 77
- Common Area 78
- Area Delay 79
- Keypad Area 79
- Configuration 80
- User Code Commands 81
- LCD Keypad Menu Programming 82
- INSTALLER MENU 83
- COM+REPORT SETTING 84
- ZONE SETTING 85
- KP/AREA SETTING 86
- SYSTEM SETTING 87
- OUTPUT SETTING 88
- RF SETTING 89
- LED/LCD Keypad Programming 90
- PC Programming 91
- 92 en 92
- Direct Connection 93
- Figure 8.13: A-Link Plus 94
- Figure 8.14: Direct link port 94
- 94 en 94
- Modem Connection 95
- 96 en 96
- Configuration 97
- 98 en 98
- Figure 8.19: Modem Connect 99
- Configuration 99
- IP Connection 100
- Configuration 101
- 102 en 102
- Configuration 103
- Figure 8.23: Network Connect 104
- 104 en 104
- Configuration 105
- 106 en 106
- Programming 107
- 108 en 108
- Programming 109
- VDS-A EN=3 110
- VDS-A=0 110
- Programming 111
- 112 en 112
- Zone Programming 113
- 114 en 114
- Programming 115
- 116 en 116
- Programming 117
- 118 en 118
- Programming 119
- 120 en 120
- Programming 121
- 122 en 122
- Programming 123
- Output Programming 124
- Programming 125
- 126 en 126
- Programming 127
- 128 en 128
- Access Codes 129
- 130 en 130
- Programming 131
- 132 en 132
- Programming 133
- 134 en 134
- System Programming 135
- Programming 137
- 138 en 138
- Programming 139
- 140 en 140
- Programming 141
- 142 en 142
- Programming 143
- Programming 145
- 146 en 146
- Programming 147
- 148 en 148
- Table 9.6: Characters 149
- Programming 149
- 150 en 150
- Table 9.7: Assign Zone Names 151
- Programming 151
- 152 en 152
- Keypad Usage and Operations 153
- 1 2 3 … 157
- Arming the System 158
- Disarming the System 159
- 1 Accessory Module Failure 160
- Power Failure 160
- Bypassing Zones 163
- Change Individual Code 165
- Keypad Panic Alarm 165
- Keypad Fire Alarm 166
- Keypad Medical Alarm 166
- Troubleshooting 167
- 168 en 168
- Troubleshooting 169
- Maintenance12 170
- Technical Data 171
- 172 en 172
- Technical Data 173
- 174 en 174
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch AMAX panel 4000 EN
(94 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.160 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce