Bosch AMAX panel 4000 EN Instalační příručka Strana 168
- Strana / 176
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AC power fault – AC power fuse is burnt. – Check if the 18V of the
transformer is correctly
wired and replace the
fuse.
Over current protection of the
auxiliary power
– Abnormal wiring of the
12V auxiliary power
– The auxiliary power
exceeds the power
supply upper limit of
2000mA for the control
panel.
– Reconnect the auxiliary
power.
– Use external power
supply for perimeter
devices.
The auxiliary power cannot be
recovered after short circuit.
– AC power and battery
fail.
– Power up AC power and
battery again.
Failure of battery is still
displayed after the battery is
replaced
– The battery might be
tested 4 hours after the
system is armed each
time.
– The voltage of the
battery is lower than
12V.
– The fault will be
automatically cleared
when the system is reset
or the battery is re-
tested.
– Charge the new battery
for a period of time until
the voltage reaches 12V
or above.
Not entering programming
mode after power up.
– The system is in alarm
state.
– The system is in arming
state.
– Reset the alarm.
– Disarm the system and
keep it in the disarming
status.
The red LED on the main
board goes off
– Abnormal AC power and
backup battery.
– The main board fails.
– Check AC power and
backup battery.
– Replace the main board
The system does not dial
when the alarm presents.
– Relevant receiver
parameters are not set.
– Correctly set the
telephone number, set
transmission format to
CID and set zone alarm
to corresponding paths.
Remote telephone arming
fails.
– The remote telephone
arming is disabled (the
address 0144 is set to
0).
– There are multiple areas
in the system.
– Program the address
0144 to a number from 1
to 15.
– The telephone arming is
available when the
system has area 1 only.
RPS cannot perform remote
programming and control.
– Both addresss 0144 and
0145 are set to 0.
– Program the address
0144 to a number from 1
to 15. Program the
address 0145 to 1.
168 en | Troubleshooting
AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
- Table of contents 3
- 4 en 4
- Table of Contents 5
- 6 en 6
- Graphics 7
- 8 en 8
- Short Information 9
- System overview 10
- Brief Introduction 11
- Address Setting 11
- Wiring and Installation 12
- Alarm Control Panel 13
- DIP Switch 16
- Status Indicator 16
- Installation 17
- Press latch 23
- Wall Tamper 24
- Address Jumper 26
- E N √ E N √ 29
- Backup Battery 30
- Installation 31
- Settings 32
- Receiver Subscriber ID Number 33
- Receiver Transmission Format 33
- 34 en 34
- Settings 35
- 36 en 36
- Settings 37
- Dual IP 38
- System Reporting 39
- Settings 41
- Settings 43
- 44 en 44
- Domestic Call 45
- Zone Inputs 46
- BBBBB7DPSHU6ZLWFK 47
- BBBBB=RQH6ZLWFK 47
- Settings 49
- Settings 51
- 52 en 52
- Settings 53
- Settings 55
- Adding and Changing Zone 57
- Onboard / Extension Output 58
- Output Events 58
- Settings 59
- Settings 61
- Output Options 63
- 64 en 64
- Settings 65
- 66 en 66
- Settings 69
- Settings 71
- Settings 73
- Settings 75
- Settings 77
- Common Area 78
- Area Delay 79
- Keypad Area 79
- Configuration 80
- User Code Commands 81
- LCD Keypad Menu Programming 82
- INSTALLER MENU 83
- COM+REPORT SETTING 84
- ZONE SETTING 85
- KP/AREA SETTING 86
- SYSTEM SETTING 87
- OUTPUT SETTING 88
- RF SETTING 89
- LED/LCD Keypad Programming 90
- PC Programming 91
- 92 en 92
- Direct Connection 93
- Figure 8.13: A-Link Plus 94
- Figure 8.14: Direct link port 94
- 94 en 94
- Modem Connection 95
- 96 en 96
- Configuration 97
- 98 en 98
- Figure 8.19: Modem Connect 99
- Configuration 99
- IP Connection 100
- Configuration 101
- 102 en 102
- Configuration 103
- Figure 8.23: Network Connect 104
- 104 en 104
- Configuration 105
- 106 en 106
- Programming 107
- 108 en 108
- Programming 109
- VDS-A EN=3 110
- VDS-A=0 110
- Programming 111
- 112 en 112
- Zone Programming 113
- 114 en 114
- Programming 115
- 116 en 116
- Programming 117
- 118 en 118
- Programming 119
- 120 en 120
- Programming 121
- 122 en 122
- Programming 123
- Output Programming 124
- Programming 125
- 126 en 126
- Programming 127
- 128 en 128
- Access Codes 129
- 130 en 130
- Programming 131
- 132 en 132
- Programming 133
- 134 en 134
- System Programming 135
- Programming 137
- 138 en 138
- Programming 139
- 140 en 140
- Programming 141
- 142 en 142
- Programming 143
- Programming 145
- 146 en 146
- Programming 147
- 148 en 148
- Table 9.6: Characters 149
- Programming 149
- 150 en 150
- Table 9.7: Assign Zone Names 151
- Programming 151
- 152 en 152
- Keypad Usage and Operations 153
- 1 2 3 … 157
- Arming the System 158
- Disarming the System 159
- 1 Accessory Module Failure 160
- Power Failure 160
- Bypassing Zones 163
- Change Individual Code 165
- Keypad Panic Alarm 165
- Keypad Fire Alarm 166
- Keypad Medical Alarm 166
- Troubleshooting 167
- 168 en 168
- Troubleshooting 169
- Maintenance12 170
- Technical Data 171
- 172 en 172
- Technical Data 173
- 174 en 174
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch AMAX panel 4000 EN
(94 stránky)
(24 stránky)
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce