Bosch KGF Series Specifikace stáhnout pdf (Strana 42)

Early

Trouble

.Shooting

Symptom

Display remains

off

after

turning on power.

air

exhausted from

working chamber.

Pressure gauge reading

remains low.

Steam

leakage

frorn lid

packing.

Water

leakage from

bottom of body.

Opedclose lever can

not

slide.

Lid cannot

~pened/closed.

Displayed temperature

:xceeds set temperature

exhausr is repeared

iequently

during the

;terilization cycle.

Cause

Check the plug

and

outlet first.

(1)

The plug is not properly inserted or

is insufficiently tightened.

(2)

Disconnection in the power cord.

(3)

Defect in DISPLAY.

(1) Defect in the automatic exhaust

valve.

(1) Defect in the safety valve.

(2) Defect in the pressure gauge.

(3)

Disconnection

the heater.

(4)

Defect in the automatic exhaust

valve.

(5)

Stem leakage.

(1)

Deterioration in the lid gasket.

(2) Improperly installed lid gasket.

(3)

Foreign matter under the gasket.

(1)

Deterioratiorl in the heater seal

packing due to lack-of-water or the

like.

(2) The drain

valve open.

(1)

Temperature in the working

chamber has exceeded

98°C

(80°C)*

or in the SOLID mode, or

pressure

the working chamber has

exceeded

0.1

kgf/cm2.

(2) The power switch is off.

(I) The open/close lever is not slid to

the end of the

open/cke

(1)

Defect in the heater circuit.

Remedy

(1)

Properly insert the plug.

t~ghren

any

loose parts.

(2)(3) Contact us or

the authorized

sales

outlet from which you purchased

the product.

(1) Contact us or

the authorized sales

outlet frorn which you purchased the

uroduct.

(1)-(4)

Replace defective part wilh new

one (Contact us or the authorized

sales outlet from which you

purchased the product).

(5)

case of stem leakage from piping,

re tighten or seal joints.

(1)

Replace the

lid

gasket with rlew

one.

(2) Uniformly push the gasket to

eliminate unevenness.

(3)

Remove the foreign matter.

(1)

outlet from which you purchased the

product.

(2)

Close the valve.

(1) Wait until temperature in the working

chamber falls below 97°C

(79°C)

in the SOLID mode and pressure

reduced to

kgf/cm2.

(2)

Turn on the power switch.

(1)

Sli&tk&closelaerto

tkcrddkqE?l/Clce2&.

(1)

outlet frorn which you purchased the

product.

Specification

for

par[icular area.

This table of early trouble shooting describes the causes of simple troubles and the

rernedies for

them. If you

find

difficulty in remedying or repairing them, contact the sales outlet

frorn

which

you purchased the product,

and

inform them of the following information:

(1)

Model and serial number of your autoclave,

(2)

Defective point(s) and symptom(s)

(and

error number if applicable),

(3)

Number of days of operation (date of purchase), and

(4)

Operating conditions (including substances

being

sterilized).

1 2 ... 37 38 39 40 41 42 43 44 45 46

Komentáře k této Příručce

Žádné komentáře

Bosch KGF Series Specifikace Strana 42

Komentáře k této Příručce

Související produkty a manuály pro ne Bosch KGF Series