Bosch Solution 144 Uživatelská příručka Strana 35
- Strana / 44
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
35Bosch Security Systems 04/12 BLCC600U
Solution 144 User Guide
Trouble Condition Description
Mains Missing
The system has detected that the AC mains supply has failed or is disconnected. If there is not a
general power outage in your area then you should contact your security company.
Battery Low
The backup battery has failed the periodic test which the system performs on a regular basis. You
should contact your security company as the battery may need replacing.
Battery Missing The system has detected that its backup battery has been disconnected.
Battery Reversed
The system has detected that backup battery has not been connected correctly.
You should contact your security company.
Voltage Low The voltage reading the keypad has fallen below the minimum level required for reliable operation.
Voltage High
The voltage reading at the keypad has increased above the maximum level required for reliable
operation.
RF Rxer Missing The system has detected that the RF receiver is disconnected.
RF Rxer Tamper The system has detected that the tamper circuit on the RF receiver is faulted.
RF Rxer Jammed
The system has registered a jamming fault from the RF receiver. This situation may preven certain
parts of your system from working correctly. You should contact your security company.
Comms Trouble R1
The system has failed to send reports to the primary report contact. You should contact your security
company.
Comms Trouble R2
The system has failed to send reports to the secondary report contact.
You should contact your security company.
Comms Test Fail
The system has failed to send its periodic report to the monitoring station.
You should contact your security company.
Buss Trouble The system has failed to communicate to a system device (e.g. keypad etc).
Default PIN Trbl
The system has detected that either the Installer PIN or User 1 PIN has not been changed from the
factory default codes. These codes should be changed immediately to prevent a security risk.
Date And Time The system date and time needs to be set.
Cabinet Tamper
The system has detected that someone has tampered with its metal enclosure or that it has been
forced open. Inspect and contact your security company if necessary.
Siren Trouble The system has detected that the external siren has failed or has been disconnected from the system.
Telco Line Trouble The system has detected that its telephone line has been disconnected for a minimum of 30 seconds.
LAN Overload
The system has detected that the current load has exceeded the maximum LAN rating.
You should contact your security company.
Comm+ Overload
The system has detected that the current load has exceeded it’s maximum COMM+ rating.
You should contact your security company.
Accessory Overld
The system has detected that the current load has exceeded it’s maximum ACCS+ rating.
You should contact your security company.
Time For Service The system displays this trouble condition to remind you that a service call is due.
Memory Fault
The system has detected an error with its internal memory.
You should contact your security company.
Default Memory The system memory has reset to factory default. You should contact your security company.
Service Mode The security installer has entered service mode.
Phone In Use The system is using the phone line.
Table 8: Control Panel Trouble Messages
- Solution 144 1
- TELEPERMIT 2
- Contents 3
- Program Menu Tree 4
- Introduction 5
- Features 5
- User’s Guide 5
- Status Icons / LED’s 7
- Keypad Tones 7
- Basic System Operation 8
- Turning An Area All On 8
- Turning The System Off 8
- Duress or Silent Alarms 10
- System Programming 10
- Erase User 10
- PIN Numbers 11
- Change Own PIN 11
- Change Other PIN 11
- Delete Token 12
- Token Status 12
- Delete PIN 12
- Add Token 12
- Edit Token 13
- RF Keyfob 13
- Add Keyfob 13
- Delete Keyfob 13
- User Name 13
- Area Assignment 14
- User Options 14
- TimeZones 14
- TimeZone Access 14
- Door Assignment 15
- User Expire Date 15
- Fingerprints 15
- Add Fingerprint 16
- Delete Fingerprint 16
- Fingerprint Status 16
- Area Status 16
- Area 1 Name 17
- Fri,Aug,13 5:34 pm 17
- Chime On/O 18
- Chime Mode 18
- Area Name 18
- Part Mode 1 Name 19
- Part Mode 2 Name 19
- Auto Arming 19
- Exit Time 20
- Reception Area 20
- Entry Time 1 20
- Entry Time 2 20
- Solution 144 User Guide 21
- OK or MENU 21
- Set Chime Zones 22
- Set Part 2 Zones 22
- OK to SAVE 23
- Output Status 24
- Turn Output On/O 24
- Output Array 25
- Door Status 25
- Door Array 25
- Door Override 26
- Output Name 26
- Door Name 26
- External Siren Test 27
- Internal Siren Test 27
- Strobe Test 27
- Communication / Reporting 27
- User Guide 28
- Destination 2 29
- Call Forward On 29
- Call Forward O 30
- User RAS PIN 30
- Email Reporting 30
- Email Address 30
- Email Options 31
- Send Test Report 31
- Devices and Optional Modules 31
- Device Status 31
- Contrast 32
- Backlight 32
- Trigger Table 1 32
- Trigger Table 2 33
- SMS Control 33
- System Events 34
- Panel Status 34
- System Trouble 34
- History Log 36
- Set Date & Time 36
- Start / Stop Day 38
- Keypad Hi/Lo Temp 39
- Site Name 39
- Walk Test All Zones 39
- Battery Test 40
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch Solution 144
(7 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce