Bosch Solution 144 Uživatelská příručka Strana 30
- Strana / 44
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Solution 144
30 Bosch Security Systems 04/12 BLCC600U
User Guide
Call Forward On
*61,*20#
Press
0-9 OK to SAVE
2. Using the numeric keys, enter all the digits of the
call forward on sequence.
You can change a single digit by scrolling the cursor
left [] and right []. For special characters (eg. , =
pause * or # etc), use the [] and [] keys.
3. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Comms > Telephone Number >
Call Forward O
MENU 5-1-7
When you enter your premises, you no longer need to
remember to manually deactivate the Call Forward feature
via the telephone. These addresses allow you to program
the Call Forward O sequence that the control panel will
automatically use to un-divert your phone when you turn
Area 1 ‘O’.
In Australia, a typical sequence of activating the Call
Forward O feature is described below:
For other countries please substitute the appropriate
commands after consultation with your telephone company.
Enter programming mode (PIN + MENU) then,
1. #61 (To turn Auto-Forward After Time - O).
2. # (End of Call-Forward sequence).
Therefore, you would program as per the following steps to
program the call forward on number as: #61#.
1. Enter [MENU] + [5] + [1] + [7].
The keypad will display the current call-forward o
sequence.
Call Forward Off
#61#_
Press
0-9 OK to SAVE
2. Using the numeric keys, enter all the digits of the
call forward o sequence.
You can change a single digit by scrolling the cursor
left [] and right []. For special characters (eg. , =
pause, * or # etc), use the [] and [] keys.
3. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Comms > Remote Access >
User RAS PIN
MENU 5-3-8
Reserved for future use
Email Reporting
In addition to Back to Base monitoring you can also
congure your alarm system to send selected reports to an
email address of your choice. To activate email reporting,
simply enter the email address in MENU 5-5-8 and then
select the required report types in MENU 5-5-9.
The Site Name in MENU 7-7-7 is used in the email subject
line when email reporting. You should also program this
name to make it easier to identify email sent by your alarm
system.
To cancel email reporting simply remove the email address
by going to MENU 5-5-8 and then pressing the [OFF] key
followed by the [OK] key.
i
Note
Currently email reporting functionality is only
available for panels located in Australia.
Comms > MyAlarm >
Email Address
MENU 5-5-8
This menu allows the master user to program an email
address that the system will send email reports to. A
maximum of 80 characters can be used to program the
email address.
1. Enter your Master PIN + [MENU].
2. Enter [5] + [5] + [8] + [OK].
The keypad will display the current email address.
Email Address
_
Press
OK to SAVE
3. Use the numeric, [0] to [9], [] and [] keys to enter
or change the email address as required.
At any time you can use the [] and [] keys to scroll
through the complete list of available characters.
To clear all characters from the cursor position to the
right, press the [OFF] key.
4. When the email address is complete, press [OK] to
save and exit, or press [MENU] to exit without saving.
To stop email reporting simply remove the email
address or disable all of the email options in MENU 5-5-
9.
i
Note
When entering an email address the @ symbol is
represented on the keypad display as .
To enter this character press the 1 key repeatedly until
the symbol appears in the display.
- Solution 144 1
- TELEPERMIT 2
- Contents 3
- Program Menu Tree 4
- Introduction 5
- Features 5
- User’s Guide 5
- Status Icons / LED’s 7
- Keypad Tones 7
- Basic System Operation 8
- Turning An Area All On 8
- Turning The System Off 8
- Duress or Silent Alarms 10
- System Programming 10
- Erase User 10
- PIN Numbers 11
- Change Own PIN 11
- Change Other PIN 11
- Delete Token 12
- Token Status 12
- Delete PIN 12
- Add Token 12
- Edit Token 13
- RF Keyfob 13
- Add Keyfob 13
- Delete Keyfob 13
- User Name 13
- Area Assignment 14
- User Options 14
- TimeZones 14
- TimeZone Access 14
- Door Assignment 15
- User Expire Date 15
- Fingerprints 15
- Add Fingerprint 16
- Delete Fingerprint 16
- Fingerprint Status 16
- Area Status 16
- Area 1 Name 17
- Fri,Aug,13 5:34 pm 17
- Chime On/O 18
- Chime Mode 18
- Area Name 18
- Part Mode 1 Name 19
- Part Mode 2 Name 19
- Auto Arming 19
- Exit Time 20
- Reception Area 20
- Entry Time 1 20
- Entry Time 2 20
- Solution 144 User Guide 21
- OK or MENU 21
- Set Chime Zones 22
- Set Part 2 Zones 22
- OK to SAVE 23
- Output Status 24
- Turn Output On/O 24
- Output Array 25
- Door Status 25
- Door Array 25
- Door Override 26
- Output Name 26
- Door Name 26
- External Siren Test 27
- Internal Siren Test 27
- Strobe Test 27
- Communication / Reporting 27
- User Guide 28
- Destination 2 29
- Call Forward On 29
- Call Forward O 30
- User RAS PIN 30
- Email Reporting 30
- Email Address 30
- Email Options 31
- Send Test Report 31
- Devices and Optional Modules 31
- Device Status 31
- Contrast 32
- Backlight 32
- Trigger Table 1 32
- Trigger Table 2 33
- SMS Control 33
- System Events 34
- Panel Status 34
- System Trouble 34
- History Log 36
- Set Date & Time 36
- Start / Stop Day 38
- Keypad Hi/Lo Temp 39
- Site Name 39
- Walk Test All Zones 39
- Battery Test 40
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch Solution 144
(7 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce