Bosch K2200 Series Specifikace stáhnout pdf (Strana 14)

Visit us at...

www.stanleypac.com

K2015B ALARM EVENT MANAGER

The K2015B Alarm Event Manager (AEM) controls and monitors other

equipment and systems on site.

The K2015B AEM is an optional device that connects a 2200/1200 door

controller and a reader. It can monitor up to eight inputs and provide eight

relay outputs. The type of door controller and the type of administration

system used determines the response to the inputs and the control of the

relay outputs.

Specific events activate the relay outputs on the K2015B to control a

variety of equipment. For example, you can activate a security camera,

turn lights on or off, or disarm an intrusion panel. You can also use these

relays for elevator control.

The inputs can also monitor equipment with a normally-open (NO) or

normally-closed (NC) contact point. For example, you can monitor

emergency exit doors, glass breaks, flood detection, and perimeter gates.

Features

Selectable two- or four-state inputs

Eight LED relay indicators

Auxiliary 12 V nominal power supply port

Eight supervised inputs, normally-open (NO) or normally-closed (NC)

Eight latched relay outputs

Steel case with tamper protection

Diagnostic display

Functions

Supervised Input: All eight inputs are fully supervised and jumper-

selectable for two- or four-state inputs. For the two-state setting no

resistors are required and only the states normal and active can be

detected.

For the four-state setting end-of-line resistors (EOL) are required and

normal, active, short (trouble), and open (tamper) states can be

detected.

Latched Relay Outputs: Each relay has a common (C), normally-

closed (NC) and normally-open (NO) contact. The relay activation time,

delay, or time limit depends on the type of door controller and the type

of administration system used. Note: Relays five to eight are only

available to systems administered by software.

Tamper Protection: Two options for tamper detection are provided:

1. A spring switch that opens when the cover is removed

2. A pair of terminals that may be taken to an external, normally

closed (NC) tamper switch.

Diagnostic Display: A diagnostic function is built-in to the K2015B

AEM. Press a button to view a two-digit display and determine the

status of each input, the tamper switch, and each relay.

Auxiliary Power Supply: The 12 V auxiliary power supply is

designed to attach equipment requiring no more than 50 mA within

32.8 ft (10 m) cable distance from the AEM. For more power or

distance use a separate power supply.

Installation/Configuration Notes

Place the K2015B AEM at any point between the door controller and

reader or other equipment. The cable distance between the door controller

and K2015B AEM must be less than 1500 ft (450 m).

Technical Specifications

Connections 6 conductor, multi-stranded, unshielded cable

Enclosure Dimensions: 5.8 in. x 7.2 in x 1.55 in. (14.8 x 18.4 x 4 cm)

Enclosure Material: 1.2 mm (18 AWG) epoxy-coated mild steel

Relative Humidity: 0% to 90%, non-condensing

Temperature (Operating): -10°C to +55°C (+14°F to +131°F)

Inputs

8 Inputs

Two-state supervised - normal or active;

Four-state supervised - normal, active,

open, short

Relay Contacts:

8 latching relay contacts with common,

normally-open (NO) and normally-closed (NC)

terminals rated at 2 A at 30 VDC

Auxiliary Power Supply: 12 V nominal at 50 mA

Current (Maximum): 50 mA

Voltage (Input):

10.2 VDC to 18 VDC provided by the door

controller

Relay 1, 2, 7 and 8

(double pole double throw)

2 A at 30 VDC and 1.8 A at 35 VAC

resistive load

Relay 3, 4, 5 and 6

(single pole double throw)

4 A at 30 VDC and 3.6 A at 35 VAC

resistive load

Ordering Information

K2015B Alarm Event Manager

Connects a 2000-series door controller with a

reader, and allows the system to perform building

management tasks. Monitors up to eight inputs

and provides eight relay outputs

K2015B 7S-K2015B

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 31 32

Komentáře k této Příručce

Žádné komentáře

Bosch K2200 Series Specifikace Strana 14

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch K2200 Series