Bosch LTC 8555 Manuál s instrukcemi stáhnout pdf (Strana 35)

Bosch Security Systems | December 8, 2004

LTC 8100, LTC 8200, LTC 8300 Series | Instruction Manual | Keyboard Operation

Moving the joystick up and to the right simultaneously

moves the camera in a diagonal direction. Rotating the

ZOOM control knob causes the lens to either zoom in or

out. The direction of its response depends on the

camera/lens model, and certain system configuration

settings that are determined at installation.

Up to four pan/tilt/zoom commands may be sent to a

remote camera site at a time (Example - Zoom In, Focus

Far, Pan Left, and Tilt Down). All three zoom lens

functions can also be sent simultaneously (Example -

Zoom Out, Focus Near, Iris Open).

12.4.2 Focus and Iris Lens Control

The lens control buttons are on the right side of the

keyboard. The camera's zoom lens, (if equipped), can be

controlled to focus near or far, and open or close the iris

(if the lens supports manual iris operation).

12.4.3 Lock or Unlock Control of a Camera

When using IntuiKey keyboards, press Device Lockout,

located on the main Allegiant menu screen to enter a

menu screen for these options.

With LTC 8555 Series keyboards, press [Lock], then

[ON] to lock a camera, or [OFF] to unlock a camera. If

the camera to be locked is not the one currently being

viewed, enter the camera number via the numeric

keyboard (but do not press [Enter]) before pressing the

[Lock].

If the Status option is enabled, the section of the on-

screen overlay between the camera number and the time

shows

indicating the camera is locked. Activating a

camera lock immediately prevents other operators (unless

they have a higher priority) from controlling the locked

pan/tilt/zoom camera. Remember to unlock the camera

when finished so other operators can access it.

12.4.4 Lock or Unlock Control of a Monitor

When using IntuiKey keyboards, press Device Lockout,

located on the main Allegiant menu screen, to enter a

menu screen with these options.

With LTC 8555 Series keyboards, press [Monitor],

[Lock], then [ON] to lock a monitor, or [OFF] to unlock

the monitor. If the monitor to be unlocked is not the one

currently being controlled by the keyboard, enter the

monitor number (but do not press [Enter]) after you

press [Monitor].

If the Status option is enabled, the section of the

on-screen overlay between the camera number and the

time shows a

indicating the monitor is locked. This

prevents other operators from changing the video on the

monitor being used (unless they have a higher priority).

Remember to unlock the monitor when finished so other

operators can access it.

If an operator with a higher priority accesses a locked

monitor and switches to a different camera, the lock is

automatically removed.

12.4.5 Recording a Camera Pre-position Scene

Select a camera with pan/tilt/zoom control with pre-

position options. Using the joystick and lens controls,

adjust the camera to view the scene you wish to store.

When using IntuiKey keyboards, press Camera Control,

located on the main Allegiant menu screen to enter a

menu screen with this option. Press Set Shot [Set], then

select the scene number via the numeric keypad, and

press [Enter]. The camera position will now be stored for

recall later.

If an AutoDome Series camera is being used, certain

pre-position commands are also used to activate

operational features/functions. Refer to the AutoDome

operation manual for complete information. If an

Allegiant conventional receiver/driver is being controlled,

the pan/tilt and zoom lens must have the necessary

options for pre-position operation.

On certain models of AutoDomes and Allegiant

Receiver/Driver Series, it is possible to disable a

previously stored pre-position, or remove it from a pre-

position tour, by pressing Set Shot [Set], the digit 9,

followed by the 2-digit pre-position number. Refer to

information supplied with the device to determine

whether it supports this feature.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 63 64

Komentáře k této Příručce

Žádné komentáře

Bosch LTC 8555 Manuál s instrukcemi Strana 35

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch LTC 8555