Bosch DS7400XiV4-EXP Uživatelský manuál stáhnout pdf (Strana 9)

DS7400XiV4-EXP

DS7400XiV4-EXP Release Notes

3.0 Known Issues in Firmware

Version 4.10

• Multiplex Devices and Address 9995: To add

multiplex devices that do not have DIP switches,

use Address 9995. However, the first zone

displayed, Zone 009, is reserved for the first

DACM door contact. Press and hold [*] until

“MUX POINT” appears on the keypad’s display.

Enter the desired zone number for the multiplex

device.

• Door Forced Open Condition Does Not Send a

Report: You must enable Addresses 3418

(Keypad Tamper) and 3419 (Keypad Tamper

Restoral) to send a Door Forced Open (DACM

Trouble 75) report.

• DACM Trouble Events Do Not Show the

DACM Number: If a DACM experiences a

trouble event, such as a Tamper (72), Missing (73),

Door Held Open (74), or Door Forced Open (74),

the keypad does not show the number for that

DACM when it displays the trouble message.

• Keypad and DACM Tamper and Restoral

Report Programming: Information on

programming keypad and DACM tamper and

restoral reports is missing from the control panel’s

documentation. Use Address 3418 for keypad or

DACM tamper reports, and Address 3419 for

keypad or DACM tamper restoral reports. If you

disable tamper and tamper restoral reports for

keypads, the keypads do not display tamper

messages. However, if you disable tamper and

tamper restoral reports for DACMs, the keypads

still display DACM tamper messages.

• DX4010i Serial Interface Module “Printer

Error” Message: The control panel generates a

“Printer Error” message if you use the DX4010i to

create a direct connection to the remote

programming software (RPS) PC.

• RPS Callback Address 3043: Enter an IP address

in Address 3043 if you want the control panel to

call the RPS PC over an Ethernet network.

• Daylight Saving Time Missing from Reference

Guide: To enable Daylight Saving Time, set

Address 3478, Data Digit 2 to “1.” To disable

Daylight Saving Time, set Data Digit 2 to “0.”

• Daylight Saving Time Not Working Correctly:

The Daylight Saving Time falls back an hour at

2:00 AM instead of 3:00 AM on the last Sunday in

October.

• Network Communication Attempts Use

AltComm Module 2 First, Then AltComm

Module 1: The control panel uses AltComm

Module 2 first before using AltComm Module 1

when attempting to communicate over an

Ethernet network. When attempting to

communicate over the telephone line, the control

panel uses Phone 1 first before using Phone 2.

• AltComm Remote Programming Callback Not

Available: You cannot program the control

panel for remote programming callback over an

Ethernet network.

• Arming An Unlocked Door: You can arm an

area when a user command latches a door access

control module’s (DACM) door open, or a fire

alarm latches a DACM’s door open.

• Fire Bell and DACM Operation: If the bell

output is set for fire and assigned to all areas

(partitions), then all DACMs in the system release

their doors during a fire alarm. If the bell output is

assigned to a certain area, only the DACMs in

that area release their doors.

• Restoral Report Not Sent for Serial Interface

Module or AltComm Module: The control

panel does not send a restoral report when a serial

interface module, or an altcomm module with the

altcomm heartbeat parameter disabled, fails and

then restores.

• Alarm Verification Not Available: Alarm

verification is not available in version 4.10 of the

DS7400XiV4.

• “Do Not Use Central Station Ack” Option and

High Network Activity: Alarm reports sent over

an Ethernet network during periods of high

network activity might not reach the central

station if the “Do Not Use Central Station Ack”

option is selected. Refer to Table 5 on page 3 for

more information.

1 2 3 4 5 6 7 8 9 10

Komentáře k této Příručce

Žádné komentáře

Bosch DS7400XiV4-EXP Uživatelský manuál Strana 9

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch DS7400XiV4-EXP