Bosch D720 Instalační příručka stáhnout pdf (Strana 18)

D9412GV3/D7412GV3 | Operation and Installation Guide | 4.0 Installation

18 Bosch Security Systems, Inc. | 2/10 | F01U143070-01

If the reset pin is placed in the disable position when

all areas are armed, there must be an entry in the

Answer Armed program item. Refer to RPS

Parameters in the D9412GV3/D7412GV3 Program

Entry Guide (P/N: F01U143071).

Locking the pin in the disable position applies power

to the control panel and charges the battery while the

detection devices and keypads are installed.

Figure 4: Reset Pin

Reset Pin

Disable All Except Battery

Charging And Programming

PERIPHERAL DEVICE CONNECTIONS

RED POWER +

YELLOW DATA BUS A

GREEN DATA BUS B

BLACK COMMON

1 - Reset pin locked (closed)

2 - Reset pin normal (open)

4.6 Completing the Installation

If not already complete, make the earth ground

connection to Terminal 10 and lock the reset pin in

the closed position.

4.6.1 Charging the Battery

Connect the battery, then the transformer to allow the

control panel to charge the battery while you complete

the installation. Refer to Section 5.0 Power Supply on

page 23 for instructions.

On-board Buzzer Sounds at Power Up and Reset:

The system performs a series of self-diagnostic tests

of hardware, software, and programming at power up

and at reset. The buzzer on the control panel sounds

during the tests. The self-diagnostics tests complete

in approximately 1 to 3 sec.

If the control panel fails any test, the buzzer continues

sounding and a System Trouble message appears at

the keypads.

Touch Terminal 10 First: If the on-board buzzer

sounds briefly when the control panel is touched, any

static charge you carry discharges to the control

panel.

Avoid electrostatic discharge. Always

touch Terminal 10, the earth ground

connection, before beginning work on the

control panel.

If the control panel receives an electrostatic

discharge, it might generate Watchdog Reset and

Param Fail events.

4.6.2 Installing and Wiring Detection Devices

Install and wire detection devices and keypads at their

locations throughout the premises. Do not connect

the control panel yet.

Section 8.0 On-Board Points on page 33 contains

instructions for wiring the on-board points to detection

devices. Section 11.0 Arming Devices on page 57

contains instructions for wiring the keypads.

Instructions for wiring the off-board point POPIT

sensor loops are found in the instructions packaged

with the POPIT modules.

4.6.3 Installing Modules and Relays

1. Power down the unit by unplugging the

transformer and disconnecting the battery.

Always power down the unit when

installing modules or relays, or when

making wiring connections to the control

panel.

2. Install and wire any modules required for the

installation as described in the module’s

installation instructions.

Instructions for the D8125 POPEX Module,

D8128D OctoPOPIT Module, D8129 OctoRelay

Module, D811 Arm Status Relay Module, and

D928 Dual Phone Line Switcher appear in this

guide.

Refer to Section 9.0 Off-Board Points on page

38 for D8125 and D8128D instructions. Refer to

Section 10.0 Off-Board Relays on page 52 for

D8129 and D811 instructions. Refer to Section

7.11 D928 Dual Phone Line Switcher on page 32

for D928 instructions.

3. If using the power outputs at Terminals 7 or 8,

refer to Section 6.4 Programmable Power Output

Terminals 6, 7, and 8 on page 27 for

instructions.

4.6.4 Connecting the On-board Points and

Keypads

Connect the on-board points and keypad wiring to the

system. Refer to Section 8.0 On-Board Points on

page 33 and Section 11.0 Arming Devices on page 57

for instructions.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 75 76

Komentáře k této Příručce

Žádné komentáře

Bosch D720 Instalační příručka Strana 18

Komentáře k této Příručce

Související produkty a manuály pro Numerické klávesnice Bosch D720