Bosch BC3200RA5 Instalační manuál

SBA8231Rev. 09/09Installation Manual Internal/External Model BC3200RABC3200RA5Service Department: 1300 30 70 37www.bosch.com.au/hotwaterTo be installe

10Installation InstructionsFilling the neutralizer unit with waterThe neutralizer unit must be filled before connecting the vent pipe.Filling the neut

11Installation Instructions7. Vent Pipe Installation• Make sure vent pipe is gas tight and will notleak. Use heat resistant silicon sealant wher-ever

12Installation InstructionsVertical Vent TerminationRoofFlashingRainCapHangerStrapSlope up wardsElbow1mMax.• Terminate at least 1.8m fromthe combustio

13Installation Instructions• Size the air inlet according with AS5601.• Be sure to provide adequate air inlet.• The air inlet needs to open to the out

14Installation InstructionsGas Connection1) Fit a union to the water heater gas inlet for easy connec-tion and removal. The thread diameter is 20 mm.

15Installation Instructions9. Water PipingThis appliance is suitable for potable water applications. Do not use this appliance if any part has been un

16Installation InstructionsSupply water piping• Do not use PVC, iron, or any piping which hasbeen treated with chromates, boiler seal or otherchemical

17Installation InstructionsPLEASE FOLLOW LOCAL CODES ABOUT CONDENSATE PIPING.• This water heater is a high efficiency, fully condensing appliance whic

18Installation InstructionsDo not connect electrical power to the unit until all electrical wiring has been completed.Consult a qualified electricianf

19Installation InstructionsRemote Controller• Applicable ModelRemote controllerRCM3211MainThe appliance BC3200RA is preset to 55°C and can be adjusted

2Installation InstructionsPotential dangers from accidents during installation and use are divided into the following threecategories. Closely observe

20Installation Instructions1. Disconnect electrical power to the water heater.2. Remove the front cover of the water heater (4 screws).3. Connect main

21Installation InstructionsWARNINGTemperature modification procedure is to compensate for temperature losses in the pipework between hot water service

22Installation InstructionsConnecting Remote Controller Cord to Unit • Keep the remote controller cord away from the freeze prevention heaters in the

23Installation InstructionsConnection between the quick connect cable and applianceConnection cordTag: "Connection cord Z shield: 2 A"AB1.Re

24Installation InstructionsUnionMake this distance as short as possible. * The hot water temperature will become unstable as the pipe lengt

25Installation Instructions13. MaintenancePeriodically check the following to ensure properoperation of the water heater.14. Trial OperationThe instal

26Installation InstructionsLighting InstructionsThis water heater does not have a pilot. It is equipped with an ignition device that automatically li

27Installation Instructions15. Dimensions(POWER CORD)< mm >HEIGHT OF EACH FITTINGFROM BOTTOM OF CASECONDENSATE DRAIN20HOTWATER OUTLET 44COLDWATE

28Installation InstructionsRemote Controller RCM3211Installation GuideFor Installers:Read this installation guidecarefully before carrying outinstalla

29Installation InstructionsRemote Controller RCS3211Installation GuideFor Installers:Read this installation guidecarefully before carrying outinstalla

3Installation Instructions1. Included AccessoriesThe following accessories are included with the unit.Check for any missing items before starting inst

4Installation Instructions3. Before InstallationDo Not Use Equipment for Purposes Other Than Those Specified• Do not use for other than increasing the

5Installation Instructions4. Choosing Installation Site* Locate the appliance in an area where water leakage from the unit or connections will not res

6Installation Instructions5. Installation ClearancesBefore installing, check for the following:The location of the flue terminal must comply with the

7Installation InstructionsItemDistance from combustibles• Maintain the following clearancesfrom both combustible andnon-combustible materials.• If the

8Installation InstructionsCLEARANCES FOR FLUE TERMINAL (front of heater)The location of the flue terminal must comply with the clearances shown on thi

9Installation InstructionsIllustration6. InstallationCheck4. Drill holes for the remaining four screws.5. Hang the unit again by the first screw, and