Bosch MBV-BPRO-40 Návod k obsluze Strana 148
- Strana / 220
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Posting interval (s; 0 = Off)
Enter the interval in seconds at which the images is sent to an FTP server. Enter zero for no
images to be sent.
FTP server
FTP server IP address
Type the IP address of the FTP server on which to save the JPEG images.
FTP server login
Type your login name for the FTP server.
FTP server password
Type the password for the FTP server.
Path on FTP server
Type the exact path where to save the images on the FTP server.
Post JPEG from camera
Select the check box to activate the camera input for the JPEG image. The numbering follows
the labeling of the video inputs on the device.
Max. bit rate
You can limit the bit rate for FTP posting.
Service > Licenses page
This page allows you to enable additional functions or software modules.
Installation code
Displays the installation code.
Activation key
Type the activation key. The activation key cannot be deactivated and is not transferable to
other units. The activation key cannot be deactivated again and is not transferable to other
units.
Installed licenses
Displays the installed licenses after their activation.
Decoder > Decoder page
Decoder profile
Allows you to set the various options for the display of video images on an analog monitor or
VGA monitor.
Monitor name
Type the name of the monitor. The monitor name facilitates the identification of the remote
monitor location. Use a name that makes it as easy as possible to identify the location.
Click
to update the name in the Device Tree.
Standard
Select the video output signal of the monitor you are using. Eight pre-configured settings for
the VGA monitors are available in addition to the PAL and NTSC options for analog video
monitors.
17.25.2
17.26
17.27
17.27.1
148 en | Encoders / Decoders page Bosch Video Management System
2012.07 | V1 | Configuration Client Configuration Manual Bosch Sicherheitssysteme GmbH
- Bosch Video Management System 1
- Table of contents 3
- Using the Help 11
- To print a Help topic: 12
- The Print dialog box opens 12
- Introduction 13
- System overview 15
- Network configuration 16
- Installing hardware 17
- Getting started 18
- Working offline 20
- Configuring devices 21
- Detecting VRM devices 25
- Configuring NVRs 25
- Configuring a Primary NVR 26
- Adding a device 29
- Configuring devices 39
- Switching on VSG recording 43
- Configuring multicast for VSG 43
- Configuring the structure 44
- Adding a Command Script 46
- Adding a camera sequence 47
- Adding a folder 47
- Managing devices on a map 49
- Adding a document 49
- Configuring schedules 51
- Removing a Task Schedule 53
- Renaming a schedule 54
- Copying and pasting in tables 55
- Configuring camera properties 56
- Configuring port settings 58
- Configuring events and alarms 60
- Creating a Compound Event 63
- Editing a Compound Event 64
- Configuring an alarm 64
- Configuring Command Scripts 66
- Creating a user 69
- Creating a group or account 70
- Configuring LDAP settings 72
- Associating an LDAP group 72
- Managing configuration data 78
- Configuration examples 81
- Adding a Bosch ATM/POS bridge 86
- Configuration window 89
- Menu commands 90
- Activation Manager dialog box 91
- Options dialog box 94
- Devices page 95
- Server List page 96
- Global Settings page 100
- Disk Storage page 100
- Camera Storage page 101
- Assigned NVRs page 102
- Assigned NVR page 102
- Vidos NVRs page 103
- DiBos page 103
- Matrix Switches page 105
- Workstation page 106
- Settings page 107
- Decoders page 108
- Analog Monitor Groups page 108
- Advanced Configuration page 109
- Monitor Wall page 110
- Communication Devices page 111
- Send Test E-mail dialog box 112
- POS + ATM page 113
- Virtual Inputs page 114
- SNMP page 115
- CCTV Keyboards page 116
- I/O Modules page 117
- Allegiant CCL Emulation page 118
- Mobile Video Service page 119
- VRM Devices page 119
- VRM Settings page 120
- Default Configuration page 122
- Load Balancing page 122
- Table 16.1: Protocol settings 125
- Devices page 125
- Live Only page 127
- Local Storage page 127
- Encoders / Decoders page 128
- Input termination 130
- Source type 130
- Select Area dialog box 133
- Tamper detection 134
- Camera > Camera page 138
- Camera > Lens page 139
- Camera > PTZ page 140
- Interfaces > Relay page 143
- Network > Advanced page 145
- Network > Multicast page 146
- Network > FTP Posting page 147
- Service > Licenses page 148
- Decoder > Decoder page 148
- Monitor display 149
- Maps and Structure page 150
- Add Sequence dialog box 152
- Schedules page 154
- Schedules page 155
- Cameras and Recording page 156
- Storage) 158
- PTZ Settings dialog box 162
- Events page 163
- Select Devices dialog box 166
- Alarms page 167
- Alarm Settings dialog box 168
- Select Resource dialog box 169
- Alarm Options dialog box 169
- Alarms page 171
- User Groups page 172
- User Group Properties page 174
- User Properties page 175
- Logon Pair Properties page 176
- Select User Groups dialog box 176
- Camera Permissions page 177
- Control Priorities 178
- Credentials page 181
- Logical Tree page 182
- Operator Features page 182
- User Groups page 183
- Priorities page 184
- User Interface page 184
- Server Access page 185
- Concepts 187
- Enterprise System 188
- Management System 192
- Troubleshooting 202
- Glossary 206
- Operator Clients 212
- Numerics 213
Související produkty a manuály pro Software Bosch MBV-BPRO-40
Software Bosch 430 Specifikace
(17 stránky)
(17 stránky)
Software Bosch BIS V3.0 Uživatelský manuál
(8 stránky)
(8 stránky)
Software Bosch IVA 4.0 Uživatelský manuál
(4 stránky)
(4 stránky)
Software Bosch PRS‑SWCS Uživatelský manuál
(3 stránky)
(3 stránky)
Software Bosch VP-CFGSFT Uživatelský manuál
(3 stránky)
(3 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce