Bosch Solution 16i Specifikace stáhnout pdf (Strana 17)

Bosch Security Systems 09/07 BLCC500R FTR1.02

Solution 16 i

Quick Start Guide

Type Meaning

Exit

Delay

Tone

After you turn an area All On, the keypad

will sound 1 short beep every second.

During the last 10 seconds fast short beeps

will be heard. If you don’t exit before the

delay time expires and an exit delay door is

faulted, an alarm occurs.

Error

Tone

If you press an incorrect key, the keypad

will sound a 2 second tone.

Mode

The keypad will sound a Hi / Lo tone to

indicate you have entered MENU Mode and

a Lo/Hi tone to indicate you have exited

MENU mode.

Chime

Tone

The keypad sounds fast short beeps to alert

you when a zone programmed for chime is

faulted or unsealled.

DTMF Control Fu nctions

Firmware version V1.10 onwards includes comprehensive

DTMF control of individual areas and outputs with full user

PIN and TIMER GROUP access veriﬁcation.

Unlike other systems, no additional hardware or modules

are required for DTMF control. To conﬁgure the desired

functions see MENU 5-3-5 DTMF Options.

How to Use DTMF Control

1. Once the panel answers the incoming call, if either option

1, 2, 3 or 4 in MENU 5-3-5 is enabled, then the panel will

play a short welcome jingle. You now have approximately

5 seconds to enter a valid PIN and log onto the panel.

2. Enter PIN followed by the # key. If the PIN is valid the

system will respond with two short beeps. If the PIN is

invalid then a single long beep will be heard.

If a valid PIN is not entered in time, the panel will attempt

to establish a modem connection as if connecting to the

Solution Link software.

If this happens you will need to hang up for approximately

60 seconds before trying again.

3. Once validated, the following commands can be

performed. See the table below. If no keys are pressed for

20 seconds then the panel will play the exit jingle before

terminating the session and hanging up. Pressing ## at any

time while connected will cause the panel to terminate the

session.

DTMF CO NTR OL FUN C TIONS

Operation Command

Response

Quick Arm

All Areas

0 + #

2 x Beeps

USER PIN + #

Welcome

Jingle

Failed

USER PIN + #

Long

Beep

Turn Area

1 + (Area Nº1-4) + 1 + #

2 x Beeps

(Low - High)

Turn Area

OFF

1 + (Area Nº1-4) + 2 + #

2 x Beeps

(High - Low)

Turn Output

2 + (Output Nº1-8) + 1 + #

2 x Beeps

(Low - High)

Turn Output

OFF

2 + (Output Nº1-8) + 2 + #

2 x Beeps

(High - Low)

End

Session

# + #

Exit Jingle

Table 8: DTMF Remote Control Functions

DTMF EXAM PLE S

Each example below shows the log on step for clarity. In

practise is only necessary to log on once per DTMF control

session.

To turn Area 1 ON enter the following

2 + 5 + 8 + 0 + #

= Log ON

1 + 1 + 1 + #

= Arm Area 1

To turn Output 10 ON enter the following

2 + 5 + 8 + 0 + #

= Log ON

2 + 10 + 1 + #

= Turn Output 10 ON

To turn Output 12 OFF enter the following

2 + 5 + 8 + 0 + #

= Log ON

2 + 7 + 2 + #

= Turn Output 7 OFF

Note

If the DTMF Quick Arm option is enabled then it is

possible to remotely arm all areas without logging

onto the panel.

Simply enter 0 + # following the welcome jingle.

Make sure that the phone being used to remotely

control the panel is set to transmit DTMF tones

when keys are pressed during the call. This option

is disabled by default on some phones.

Expansion M odu les

CM704B Zone Expander Module

The Solution 16i panel includes support for 1 x CM704B -

8/16 Zone Expansion module. This allows for 16 individual

zones when using Alarm and Tamper (4 state) monitoring

as well as allowing zones to be located in two separate

locations within a building.

All zones follow the global EOL setting in MENU 3-4-0

regardless of whether they are on the panel or on the

expander module.

Zone numbering is automatically assigned by the panel

during power up depending on the module conﬁguration

found and the EOL value selected.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 43 44

Komentáře k této Příručce

Žádné komentáře

Bosch Solution 16i Specifikace Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Bosch Solution 16i