Bosch D720 Specifikace stáhnout pdf (Strana 7)

D9412G/D7412G/D7212G Installation & Troubleshooting Quick Reference Guide

D9412G/D7412G / D7212G

Quick Reference Terminal Description

2.0 Quick Reference Terminal Description

Terminal Name Description

1, 2

CLASS 2

TRANSFORMER

Connect 16.5 VAC, 40 VA transformer for primary power supply.

3 + AUX POWER

Supplies up to 1.4 A at 10.2 VDC to 13.9 VDC to powered devices. Use Terminal

9 for common. Shares PTC with Terminal 24.

BATTERY

NEGATIVE ONLY

Connect rechargeable lead acid type battery’s negative terminal (-) to Terminal

4. (See the Current Rating Charts section in the panel’s Approved Applications

Compliance Guide to determine battery size requirements.)

5 (+)

BATTERY

POSITIVE ONLY

Connect rechargeable lead acid type battery’s positive terminal (+). (See the

Current Rating Charts section in the panel’s Approved Applications Compliance

Guide to determine battery size requirements.)

6 (+)

+ STEADY OR

PULSED ALARM

POWER

Supplies up to 2 A at 10.2 VDC to 13.9 VDC for steady or pulsed alarm output.

Use Terminal 9 for common. Programmed as Relay A. Shares PTC with

Terminals 7 and 8.

7 (+)

+ ALTERNATE

ALARM POWER

Supplies up to 2 A at 10.2 VDC to 13.9 VDC for steady or pulsed alarm output.

Use Terminal 9 for common. Programmed as Relay B. Shares PTC with

Terminals 6 and 8.

D136 Plug-in Relay required: Install a D136 in the ALT ALARM socket for

output at Terminal 7.

8 (+)

+ SWITCHED

AUX POWER

Supplies up to 1.4 A at 10.2 VDC to 13.9 VDC. Use Terminal 9 for common.

Programmed as Relay C. Continuous output interrupted by RESET SENSORS

or alarm verification. Shares PTC with Terminals 6 and 7.

D136 Plug-in Relay required: Install a D136 in the SW AUX socket for output at

Terminal 8.

9 COMMON

Terminal 9 is common for Auxiliary Power, Steady or Pulsed Alarm Power,

Alternate Alarm Power, and Switched Aux Power (Terminals 3, 6, 7, and 8).

10 EARTH GROUND

Connect to earth ground. A cold water pipe or grounding rod is preferred.

Do not connect to telephone or electrical ground.

11, 13, 14,

16, 17, 19,

20, 22

ON-BOARD

POINTS

(Inputs)

Connect normally open and/or normally closed detection devices to loop wiring.

1 kΩ resistor required at end of loop.

12, 15, 18,

ON-BOARD

POINTS

(Common)

Loop returns for on-board points.

23 (-)

ZONEX

COMMON

24 (+) ZONEX POWER +

[D9412G only] Use Terminals 23 and 24 to power ZONEX modules such as

the

D8125 POPEX module, the D8128D OctoPOPIT, and the D8129 OctoRelay.

Shares PTC with Terminal 3.

25 ZONEX IN 2

26 ZONEX OUT 2

[D9412G only] Connect ZONEX modules for Points 129 to 247 and Relays

65 to 128 to these terminals.

27 ZONEX IN 1

28 ZONEX OUT 1

Connect ZONEX modules for Points 9 to 127 and Relays 1 to 64 to these

terminals. (The D7412G uses Points 9 to 75, the D7212G uses Points 9 to 40.)

29 (-) COMMON Common terminal for SDI devices.

30 DATA BUS B

31 DATA BUS A

Terminals 30 and 31 are a two-wire bus that drives the command centers,

printer interface, and access control modules including the D9133TTL-E

Ethernet Interface Module, D9133DC Direct Connect Module, D9133 Serial

Interface Module, and the PC9133TTL-E Ethernet Interface Module.

32 (+) POWER +

Power for SDI devices. Shorts on any other terminal do not affect this separate,

protected power output for SDI devices.

Table 3: Quick Reference Terminal Description

1 2 3 4 5 6 7 8 9 10 11 12 ... 31 32

Komentáře k této Příručce

Žádné komentáře

Bosch D720 Specifikace Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Numerické klávesnice Bosch D720