Bosch D9112B Uživatelská příručka

Security SystemUser’s Guide

If there are bypassed points, AREA 1 ## BYPAS (## =total number of bypassed points) is displayed, followedby the point text descriptions of the bypas

The group with the highest priority scrolls first in the commandcenter’s display. Descriptions of the tones and displays for eachgroup and instruction

Fire AlarmsFire alarms are the highest priority events. When a fire pointactivates, your command center emits a pulsating high-pitchedfire tone. Evacu

See VIEW MEMORY? (COMMAND 40) for more information.To clear the event memory and remove the ALARM SILENCEDmessage from the display, enter a valid pas

Fire Trouble EventsWhen a fire trouble occurs, your command center emits threewarble tones, then a pause (repeatedly).The system displays the number o

Non-Fire Trouble EventsWhen a trouble event such as an AC failure occurs, yourcommand center may be programmed to emit three warble tones,then a pause

Entry Delay Tone and DisplayWhen you enter an armed system through a point programmedfor entry delay, the command center emits a repeating tweedletone

Keystroke Checking TonesValid EntryIf you press an appropriate key for the function or entry youdesire, the command center sounds a muted beep tone, i

System Commands & FunctionsBelow is a summary of the commands covered in this guide. Some of these functions may not be available in your system.

Turning the System On (Arming)Your security system can be turned on (armed) in many differentways, depending on the arming command used. ArmingCommand

Turning the System Off (Disarming)Your security system is turned off by entering your personalpasscode. When the system is turned on, you must enter t

Turning the System On (Arming) WithDoors or Windows OpenIf a protected door or window is open, you may have the optionof “force arming” with that poin

NOT AUTHORIZEDThe authority level for your passcode does not give youthe authority to force arm.5. Press ENT with FORCE ARM displayed to arm yoursyst

MASTER ARM ? Turn the Entire System On With DelaysDescriptionUse this function to turn on the entire system, both perimeterand interior. When you tur

Using Master Arm Inst:1. The display shows idle disarmed text.2. Press the COMMAND bar. The display shows SYSTEMCOMMAND.3. Press the 1 key. Now press

PERIMETR INST ? Turn On the Perimeter With No DelaysDescriptionUse this function to turn on only the perimeter of your building,leaving the interior

PERIMETR INST ? continued5. To disarm your security system, enter your personalpasscode and press ENT.

Using Perimetr Delay:1. Interior points are not armed with this command andmay remain faulted while arming with COMMAND 3.2. Press the COMMAND bar. Th

Page CodeTable of ContentsIntroductionCommand Center Function KeysSecurity System BasicsYour Custom DisplayView Faulted or Bypassed PointsWarning

Silence the Trouble Sounder & ClearTrouble Display DescriptionUse COMMAND 4 to silence the trouble sounder during systemevents. This command also

VIEW MEMORY ? View Event MemoryDescriptionYour system stores events that occurred since the last timememory was cleared. Use COMMAND 40 to view Event

WALK TEST ? Walk TestDescriptionUse this function to test command centers, detection devices,and sounders (both interior and exterior) to be certain

WALK TEST ? continued4. The burglary bell sounds for 2 seconds. When the displaypanel shows ## PTS TO TEST you can begin. Test eachpoint by first ope

3. Press the 4 key followed by the 7 key.Note: If you prefer, you may use the Command Menu in placeof steps 2 and 3 to initiate this function. Press t

WATCH MODE ? Watch ModeDescriptionWith your security system disarmed, you can use watch mode tomonitor some points. Each time some points are faulted

Siren/Speaker1234567890COMMANDESCPREVNEXTENTALL INSTANT DELAYRESET WATCHSPECIAL PARTIAL POLICEBYPASSMENU YESAREAXISOFFAlphanumeric DisplayDigital Keyp

Exiting Watch Mode continued2. Press the COMMAND bar. The display shows SYSTEMCOMMAND.3. Press the 6 key.Note: If you prefer, you may use the Command

PERIMETR PART ? Partially Turn On the PerimeterDescriptionThis function is used to turn on the perimeter of your buildingwhile selected portions of t

PERIMETR PART ? continued5. When performing a COMMAND 8 and no points arefaulted or if the points return to normal before the exitdelay time expires,

Using COMMAND 7:1. Press the COMMAND bar. The display shows SYSTEMCOMMAND.2. Press the 7 key. Your COMMAND 7 special alert has beenprogrammed to:___ n

Using COMMAND 9:1. Press the COMMAND bar. The display shows SYSTEMCOMMAND.2. Press the 9 key. Your COMMAND 9 special alert has beenprogrammed to:___ n

Security System LimitationsNot even the most advanced security system can guaranteeprotection against burglary, fire, or environmental threats. Allsec

Fire Safety and EvacuationResidential fire is a leading cause of accidental death. Most firerelated deaths occur at night when occupants suffocate in

Fire Safety and Evacuation continuedPlan both primary and alternate escape routes. Since stairwellsand hallways may be blocked during a fire, exiting

NO AUTHORITYThe system does not recognize the passcode entered.NOT AUTHORIZEDThe passcode entered does not have the authority to Force Arm.PERIMETR

System Trouble DisplaysIf you see any of the system trouble displays shown below, contactyour security company to determine whether repairs are needed

IntroductionYour security system helps to secure life, property, andinvestments against fire, theft, and bodily harm. The commandcenter is an advanced

SERVC PH LINE #1 (or 2)Indicates telephone line trouble. Call your phone company fromanother phone to report telephone trouble. This message maynot

Security System GlossaryArea - A group of detection devices connected to your securitysystem.Arm - To turn your controlled points (burglar detectionde

Force Arm - To turn on (arm) the security system even thoughone or more points are faulted. Force arming bypassesthe faulted points.Idle Text - The se

YOUR ALARM COMPANY IS CALL BEFORE TEST___________________Maintenance and ServiceThis security system requires very little maintenance, however,you

71-06141-000-C 02/03 D9112B

Command Center Function KeysYour command center has five function keys. These keys are usedto control your system.COMMANDUse the COMMAND bar in combin

Security System BasicsWhat is a Point?A “point” is a detection device, or group of devices connected toyour security system. Points display individual

24-Hour Points24-hour points are always on, even when the burglary system isdisarmed (turned off). There are two types of 24-hour points,fire points a

Your Custom Display“At an idle state” means that the system is not currently performing a function entered by a user. There are three idle states thes