Bosch VJD-3000 Instalační manuál

VIDEOJET decoder 3000VJD-3000 en Installation Manual

Connections, controls and displaysFront view1 HDMI monitor socketfor connecting a computer monitor via HDMI cable2 VIDEO OUT video outputBNC socket fo

Rear view1 ETH RJ45 socketfor connecting to an Ethernet LAN (local network), 10/100 MBit Base-T2 LED LINKlights up when the unit is connected to the n

InstallationPreparationsVIDEOJET decoder 3000 and the power supply unit are both intended for use indoors or inhousings. Select a suitable location fo

3. Check that the plastic frame is secure.4. Place the unit on the wall-mounting panel, with the panel positioned between the housingand the second pl

14 en | Installation VIDEOJET decoder 30002014.01 | V4 | F.01U.296.741 Installation Manual Bosch Sicherheitssysteme GmbH

ConnectionConnecting monitorsYou must connect a suitable monitor to the decoder. The unit provides two monitor outputs.Simultaneous use of both output

Connecting audioThe unit has two audio ports for audio line signals.The audio signals are transmitted two-way and in sync with the video signals. The

Establishing the network connectionYou can connect the unit to a 10/100 Base-T network using a standard UTP category 5 cablewith RJ45 plugs.4 Connect

!Caution!Please observe the labeling on the unit.1. Connect the lines to the appropriate terminals on the terminal block (IN1 to IN4) andcheck that th

The range of controllable equipment is expanding constantly. The manufacturers of therelevant equipment provide specific information on installation a

!Caution!Make sure to use the power supply unit provided only with the correct primary adapter foryour power outlet or use another power supply unit w

ConfigurationSetupBefore you can operate the unit within your network, it must have a valid IP address for yournetwork and a compatible subnet mask.No

Additional parametersYou can check and set additional parameters with the assistance of the Configuration Managerapplication in Bosch Video Client. Yo

TroubleshootingContactIf you are unable to resolve a malfunction, please contact your supplier or systems integrator,or go directly to Bosch Security

Malfunction Possible causes Recommended solutionNo alarm response specified. Specify the desired alarmresponse, change the IPaddress, if necessary.Con

Processor loadIf the unit is accessed via the Web browser, you will see the processor load indicator bar inthe top right of the window next to the inf

Pin assignment I/OContact FunctionIN1 Input alarm 1IN2 Input alarm 2IN3 Input alarm 3IN4 Input alarm 4GND GroundR Relay outputConnect each alarm input

MaintenanceUpdatesFirmware updates are carried out via our Video Client software or other management systemsin use. Please refer to the relevant docum

DecommissioningTransferVIDEOJET decoder 3000 should only be passed on together with this installation manual.DisposalYour Bosch product is designed an

Technical dataElectricalInput voltage 12 V DCInput current 0.75 APower consumption 9 WMechanicalDimensions (H × W × D) 38 × 146 × 178 mm (1.5 × 5.7 ×

Table of contents1Safety 51.1 Electric shock hazard 51.2 Installation and operation 51.3 Maintenance and repair 62Short information 72.1 About this ma

StandardsVideo standards PAL, NTSC, HDMIVideo coding protocols H.264 High Profile, H.264 Main Profile, H.264 Baseline Profile(ISO/IEC 14496-10)M-JPEG,

IndexAAlarm, 11Alarm input, 17Analog video, 10Audio connections, 10, 16CClosing contact, 17Conventions, 7DDanger, 5Data interface, 18DefaultIP address

Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2014

10Technical data 2910.1 Electrical 2910.2 Mechanical 2910.3 Environmental conditions 2910.4 Standards 30Index 314 en | Table of Contents VIDEOJET deco

SafetyElectric shock hazard– Never attempt to connect the unit to any power network other than the type for which itis intended.– Use only the power s

– Avoid impacts, blows, and severe vibrations that exceed the specification limits, as thesecan irreparably damage the unit.Maintenance and repair– Ne

Short informationAbout this manualThis manual is intended for persons responsible for the installation and operation of aVIDEOJET decoder 3000 unit. I

System overviewParts included– 1 VIDEOJET decoder 3000 video decoder– 2 terminal blocks (6-pin, 8-pin)– 4 self-adhesive elastic bumpers– 1 wall-mounti

VIDEOJET decoder 3000 provides one-channel bidirectional audio communication in parallelto video.Ultra-compact in size, VIDEOJET decoder 3000 is perfe